When it comes to washing machines, the Maytag brand is recognized for its dependability. Maytag washers have complex electrical systems and parts that work together smoothly. But if there is a problem, your washing machine has a system of diagnostic codes that will signal discrepancies. Yet, understanding and fixing these problem codes could be difficult.
Fortunately, Man With a Wrench has a crew of knowledgeable appliance technicians who can resolve any Maytag washer error code. Refer to the explanations of the fault codes listed below for help troubleshooting a Maytag washing machine.
Please do not hesitate to contact our customer service agents if you require assistance. In addition to the adjacent areas of Toronto, Vaughan, Brampton, Mississauga, Markham, Newmarket, and Oakville, they are accessible to schedule service for top load washers or front load washers.
How To Clear An Error Code
In addition to fixing the underlying issue that caused the error code, another frequently used strategy is briefly unplugging the washer to cut off the power. Reconnecting the power supply often removes the error code (at least momentarily), depending on the nature of the problem.
Although the error code may appear to have disappeared, it’s still essential to deal with the problem’s core cause rather than try to avoid it because doing so may worsen the washer’s damage or produce a flood in the laundry room.
But occasionally, a control board malfunction may cause an error code. In some situations, fixing the issue only requires cutting the power.
Error Codes in your Maytag Top Load Washer
Error Code: F# E# or F##
Condition:
This error code represents a system error in the washing machine.
Possible Resolution:
To clear the error code, press the START/PAUSE button once. Then, press the START/PAUSE button again to restart the washer. If the error code persists, please contact us or schedule a service for professional assistance.
Error Code: HC
Condition:
Hot and cold inlet hoses are installed incorrectly.
Possible Resolution:
Turn off the water supply and reverse the hot and cold hoses. After correcting the hose connections, run another cycle to ensure proper functionality.
Error Code: LdL
Condition:
The washer’s lid is not locking properly.
Possible Resolution:
Check for obstructions on the lid and ensure the lid lock mechanism is free from detergent buildup. Clear any blocks to allow the cover to lock securely.
Error Code: drn
The washer’s drainage is not working correctly. This error code suggests that the washing machine’s basin’s water level may be complete or partially empty.
Condition:
Water isn’t draining
Possible Resolution:
The Maytag washing machine error code drn may indicate that the washer is not draining correctly. Verify that the terminus of the drain pipe is 36 to 96 inches above the ground. Make sure that the 36-inch threshold requirement is met at the installation point.
Error Code: LdU
Condition:
The washer’s lid cannot unlock.
Possible Resolution:
Remove any objects that might be obstructing the washer lid. Once cleared, the lid should be able to unlock correctly.
Error Code: LF, Lo FL or F8 E1
Condition:
The washer is taking too long to fill with water.
Possible Resolution:
Ensure that both the hot and cold water faucets are fully open. Verify that the household water supply is turned on. Make sure to use HE detergent for proper water fill.
Error Code: Ofb
Condition:
The washer load is out of balance.
Possible Resolution:
Allow the washer to complete its load-balance correction routine. If needed, evenly redistribute the items in the drum around the wash plate to balance the load.
Error Code: OL
Condition:
The washer load is too large.
Possible Resolution:
Remove excess items from the washer drum. Add HE detergent if required. Close the lid and press START/PAUSE to continue the cycle.
Error Code: PF
Condition:
A power failure stopped the wash cycle.
Possible Resolution:
To resume the cycle, press and hold the START button. Press the POWER button to clear the display and restart the washer.
Error Code: Sud
Condition:
There are excessive suds in the washing machine.
Possible Resolution:
To avoid extra suds, always use HE High-Efficiency Detergent. If you’re using “no splash” or “easy pour” liquid chlorine bleach, run the washer with conventional liquid bleach products. Check for any obstructions in the drain line or standpipe that could contribute to the excessive suds.
Error Codes in my Maytag Front Load Washer
Error Code: LOC or LC
Condition:
Control Lock has been activated.
Possible Resolution:
To deactivate the control lock, press the Control Lock button. On specific models, pressing down the button may be required. Refer to your Owner’s Manual for detailed instructions.
Error Code: dET
Condition:
The detergent cartridge was not detected in the dispenser.
Possible Resolution:
If using single-load detergent, you can ignore this message. Ensure the dispenser cartridge is inserted correctly and the drawer is completely closed.
Error Code: Int
Condition:
The cycle was paused or cancelled.
Possible Resolution:
During the stop or cancel process, the washer may take 20 to 30 minutes to stop spinning and drain. To remove the error code, press the stop or cancel button twice and the power button once. If the code persists, unplug the washer or disconnect the power for one minute.
Error Code: rL or F34
Condition:
During the Clean Washer cycle, items were detected in the washer.
Possible Resolution:
Remove any items from the drum and restart the Clean Washer cycle.
Error Code: Sud or Sd
Condition:
Excessive suds in the washing machine.
Possible Resolution:
Excessive suds prevent the washer from spinning. “Sud” or “Sd” indicates extended rinsing is required. Always use HE detergent. Also, check the type of liquid chlorine bleach used. Remove any clogs in the drain hose.
Error Code: F5 E2
Condition:
The door is not locking properly.
Possible Resolution:
Check the door for any obstructions and ensure it closes completely. To clear the code, press the stop or cancel button twice and the power button once.
Error Code: F7 E1
Condition:
Motor speed sensing error.
Possible Resolution:
Examine the washer load and distribution, and ensure all shipping bolts have been removed. To clear the code, press the stop or cancel button twice and the power button once.
Error Code: F8 E1 or LO FL
Condition:
Low water flow sensed.
Possible Resolution:
Check for kinks in the water supply and inlet hoses. Ensure there are no anti-flood hoses or controls attached. To clear the code, press the stop or cancel button twice and the power button once.
Error Code: F8 E2
Condition:
Dispenser System problem.
Possible Resolution:
Check the detergent drawer or cartridge for clogs. Clean the washer dispensers if necessary.
Error Code: F9 E1
Condition:
Drain times longer than expected.
Possible Resolution:
Check the drain hose for kinks or clogs. Use a U-shaped drain hose form. Confirm the height of the standpipe. Excessive suds can cause delays; use HE detergent.
Error Code: Other F# E# code
Condition:
Other errors.
Possible Resolution:
Unplug the washer or disconnect the power for one minute. Reconnect and select a cycle. If the code persists, contact the service for a diagnosis.
Contact Man With A Wrench for Washer Appliance Repair
Man With a Wrench is your go-to service for proper troubleshooting, replacement, or Maytag appliance repair with friendly and experienced repairmen. Call us at 1-888-416-3963, book a virtual diagnostic, or fill out our convenient online form to find out how we can help you.
We understand that most of the repairs needed in your home can’t wait for a service team to squeeze you into their schedules. That’s why we offer same-day service, so you don’t have to wait.
